ML4800CP【PDF 10/14 页】IC PFC CTRLR AVERAGE CURR 16DIP

ML4800

PRODUCT SPECIFICATION

10

REV. 1.0.5 9/25/01

Oscillator (RAMP 1)

The oscillator frequency is determined by the values of R

T

and C

T

, which determine the ramp and off-time of the

oscillator output clock:

The dead time of the oscillator is derived from the following

equation:

at V

REF

= 7.5V:

The dead time of the oscillator may be determined using:

The dead time is so small (tRAMP >> t

DEADTIME

) that the

operating frequency can typically be approximated by:

EXAMPLE:

For the application circuit shown in the data sheet, with the

oscillator running at:

Solving for R

T

x C

T

yields 1.96 x 10

-4

. Selecting standard

components values, C

T

= 390pF, and R

T

= 51.1k&.

The dead time of the oscillator adds to the Maximum PWM

Duty Cycle (it is an input to the Duty Cycle Limiter). With

zero oscillator dead time, the Maximum PWM Duty Cycle is

typically 45%. In many applications, care should be taken

that C

T

not be made so large as to extend the Maximum Duty

Cycle beyond 50%. This can be accomplished by using a

stable 390pF capacitor for C

T

.

PWM SECTION

Pulse Width Modulator

The PWM section of the ML4800 is straightforward, but

there are several points which should be noted. Foremost

among these is its inherent synchronization to the PFC

section of the device, from which it also derives its basic

timing. The PWM is capable of current-mode or voltage

mode operation. In current-mode applications, the PWM

ramp (RAMP 2) is usually derived directly from a current

sensing resistor or current transformer in the primary of the

output stage, and is thereby representative of the current

owing in the converters output stage. DC I

LIMIT

, which

provides cycle-by-cycle current limiting, is typically con-

nected to RAMP 2 in such applications. For voltage-mode

operation or certain specialized applications, RAMP 2 can

be connected to a separate RC timing network to generate a

voltage ramp against which V

DC

will be compared. Under

these conditions, the use of voltage feedforward from the

PFC buss can assist in line regulation accuracy and response.

As in current mode operation, the DC I

LIMIT

input is used

for output stage overcurrent protection.

No voltage error amplier is included in the PWM stage of

the ML4800, as this function is generally performed on the

output side of the PWMs isolation boundary. To facilitate

the design of optocoupler feedback circuitry, an offset has

been built into the PWMs RAMP 2 input which allows V

DC

to command a zero percent duty cycle for input voltages

below 1.25V.

PWM Current Limit

The DC I

LIMIT

pin is a direct input to the cycle-by-cycle

current limiter for the PWM section. Should the input

voltage at this pin ever exceed 1V, the output of the PWM

will be disabled until the output ip-op is reset by the clock

pulse at the start of the next PWM power cycle.

V

IN

OK Comparator

IN

OK comparator monitors the DC output of the PFC

FB

is less than its

nominal 2.45V. Once this voltage reaches 2.45V, which

corresponds to the PFC output capacitor being charged to its

rated boost voltage, the soft-start begins.

PWM Control (RAMP 2)

When the PWM section is used in current mode, RAMP 2

is generally used as the sampling point for a voltage

representing the current in the primary of the PWMs output

transformer, derived either by a current sensing resistor or a

current transformer. In voltage mode, it is the input for a

ramp voltage generated by a second set of timing compo-

nents (R

RAMP2

, C

RAMP2

), that will have a minimum value of

zero volts and should have a peak value of approximately 5V.

In voltage mode operation, feedforward from the PFC output

buss is an excellent way to derive the timing ramp for the

PWM stage.

Soft Start

Start-up of the PWM is controlled by the selection of the

external capacitor at SS. A current source of 25礎 supplies

the charging current for the capacitor, and start-up of the

PWM begins at 1.25V. Start-up delay can be programmed by

the following equation:

f

OSC

1

t

RAMP

t

DEADTIME

+

--------------------------------------------------- -

=

(2)

t

RAMP

C

T

R

T

?/DIV>

In

V

REF

1.25

V

REF

3.75

----------------------------- -

?/DIV>

=

(3)

t

RAMP

C

T

R

T

?/DIV>

0.51

?/DIV>

=

t

DEADTIME

2.5V

5.5mA

---------------- - C

T

?/DIV>

450 C

T

?/DIV>

=

(4)

f

OSC

1

t

RAMP

--------------- -

=

(5)

f

OSC

100kHz

1

t

RAMP

--------------- -

=

C

SS

t

DELAY

25礎

1.25V

-------------- -

?/DIV>

=

(6)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式